I believe what you're looking for are the Roller Catches for RV Cabinets # 37270255 which measure 3/8" wide. These are the exact same style as the one you were looking at - they are just smaller.
Attached is a review video for you to check out! view full answer...
The Dual Function Air Spring Control Panel # F2260 that you referenced would be just what you'd need to give you the ability to have two different psi levels in two different areas like you mentioned. The black arrow would show you how much pressure is in one set and the red in the other. view full answer...
On your 1996 motorhome that's on a Chevrolet P30 chassis you want part # AL57219 if the GVWR is over 14,500 pounds or part # AL57203 if it's less than 14,500 pounds. view full answer...
If you're talking about adding a fan to the Ventline Ventadome Trailer Roof Vent # V2110SP-24 then no, you wouldn't be able to add a fan and would need to purchase a vent that already includes a fan like the Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-30. You can splice into the 12v power that's already there to power this vent and make the installation easier.
To complete the installation you'll also need some butyl tape # AL28FJ and self-leveling sealant # 34427034145-1... view full answer...
Go Power Retreat Solar Charging Kit w/ Digital Controller - 100 Watts - 5.43 Amp # 34272635 is expandable to multiple panels using the Go Power Retreat-E Expansion Kit - 100 Watts - 5.43 Amp # 34272634.
If you want more power, you may want to consider the The Go Power Overlander-E Expansion Kit # 34282182 which can add the Go Power Overlander Solar Charging Kit w/ Digital Controller # 34282181 to give you a larger system.
Either option can be expanded with more panels as desired. I've... view full answer...
Since you're using two air conditioners, the 13,500 Btu air conditioner will give you more than enough cooling, so you can go with a unit from Advent:
- Advent Air RV Air Conditioner w/ Air Distribution Box and Wall Thermostat - 13,500 Btu # ADV94FR view full answer...
The front Firestone Coil-Rite Air Helper Springs # F4100 is the correct kit for a 1994 Chevy Class A chassis (should be the P-30) you have for your Winnebago motorhome!
If you're looking for rear air bags as well then you need one of the following depending on the GVWR of your RV:
- GVWR Less Than 14,500 lbs # AL88203
- GVWR Greater Than 14,500 lbs # AL88219 view full answer...
If your P30 wheels are 19.5 inch diameter wheels with 10 lugs and 10 hand holes the Namsco Hub Cap Wheel Cover # NA7195B1 will fit the wheels. view full answer...
I reached out to Roadmaster, and did some of my own research, and the correct part for your 1996 Fleetwood on a Chevy P30 is # RM-RBK3-RSSP30. The OEM damper doesn't become an issue until the 1998 model years. view full answer...
From the picture you have provided it looks like you already have the Quick Disconnect Crossbar Assembly for Roadmaster Tow Bars # 910021-00 so you should be good to connect to the Roadmaster Crossbar-Style Base Plate Kit # 909-9. I don't see the mounting hardware or safety plates so if you need replacements you can get them with part # RM-222.
I've attached a couple videos below to help guide you through the installation process. view full answer...
From what I could find, the 1995 Winnebago Brave could have come with 4 different chassis. Two Chevrolet, one Ford, and one Oshkosh. The Timbren Front Suspension Enhancement System # TWFRW22 is designed to fit a Chevy P42 chassis (from 1975 to 1997), so if this matches what you have, then yes, these will replace the factory jounces.
If this isn't the chassis you have though, let me know which you have and I can get a better fit for you. view full answer...
No, the Roadmaster Rear Anti-Sway Bar # RM-1259-109 is not a confirmed fit for your P-Series Chassis. The only anti-sway bar that we carry for a P-Series Chassis like your 1995 Georgie Boy would be the Roadmaster Front Anti-Sway Bar and Bushing Kit # RM-1109-116. view full answer...
In order to haul a generator on the front of your vehicle, I suggest using a front mount trailer hitch such as the # 13703. This is an adjustable type hitch that fits frames from 22" to 72" in width. It is not a custom fit but will require a little bit of fabrication and some welding. Curt states that all non-trailered loads need to be secured with Stabilizing Support Strap # 18050. After installation of adjustable hitch, you can use a cargo basket carrier such as the Curt Cargo Carrier... view full answer...
10 gallon water heaters draw more amperage to heat which is why we have the part # CAM11773 which is for this size water heater. The part # CAM11673 would not have the power to effectively heat a 10 gallon setup. view full answer...
The Roadmaster Reflex Steering Stabilizer, # RM-RBK3-RSSP30, is the correct stabilizer for your 1991 Chevrolet P30 Motorhome. Everything you will need is included, stabilizer, custom mounting brackets, and hardware. No drilling or welding is required so installation should take about 1 hour. view full answer...
I recommend looking at the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07. This is a universal receiver you can use as there currently is not a custom fit receiver for your 1985 Itasca Sunflyer on a Chevrolet P30 chassis. This particular receiver can be welded or bolted to the frame and uses 7" tall brackets. We do have the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-16 that uses 16" long brackets depending on the amount of drop you need on the... view full answer...
You are correct, the 1994 Chevrolet P-Series Chassis came with both two wheel drive front coil spring suspension and four wheel drive front leaf spring suspension setups. Fortunately, we have stabilizer and sway control options for both models.
For your coil spring suspension, I recommend using both a front steering stabilizer and rear axle stabilizer. For the front steering stabilizer, I recommend using the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Motor Homes... view full answer...
SumoSprings Solo Custom Helper Springs # SSR-290-54 will fit your 1996 Chevrolet P32 and they are for the rear axle.
If you axle need suspension enhancement for the front axle you can use the Timbren # TUF100. view full answer...
For a motorhome on a P30 chassis with a 36" frame width you would need to install an adjustable-fit hitch like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07. The cross tube for this hitch is 44" in length but can be trimmed down to fit your chassis. The mounting brackets have a 7" drop to help clear your rear fascia, but we also offer this with a 16" drop # 41990-16 if needed. view full answer...
I went ahead and reached out Lippert and they were able to tell me that the mounting screws on the Replacement 2-Quart Pump Reservoir Kit for Lippert Components Hydraulic Power Unit # LC46FR measure 3" from the top screw to the bottom screw, and 3-1/2" across.
Additionally, they did also mention that the O-ring is 3-1/2" in diameter.
For a replacement o-ring, you can use the:
-Oil Cap O-Ring # 92127.
I have included a diagram and a review video for you to check out if you have not alerady. view full answer...